2/17/2024 0 Comments Actual size metric mm chartHowever, as the set of available wall thicknesses evolved, the ID changed and NPS became only indirectly related to ID and OD.įor a given NPS, the OD stays fixed and the wall thickness increases with schedule. The reason for the discrepancy for NPS 1⁄ 8 to 12 inches is that these NPS values were originally set to give the same inside diameter (ID) based on wall thicknesses standard at the time. In other words, an NPS 14 pipe is actually 14 inches (360 mm) OD. For NPS 14 and up, the NPS and OD values are equal.(Note that for tubing, the size indicates actual dimensions, not nominal.) To find the actual OD for each NPS value, refer to the tables below. For example, the OD of an NPS 12 pipe is actually 12.75 inches (324 mm). For NPS 1⁄ 8 to 12, the NPS and OD values are different.However, the NPS and OD values are not always equal, which can create confusion. For example, NPS 14 Sch 40 has an OD of 14 inches (360 mm) and a wall thickness of 0.437 inches (11.1 mm). Due to their thin walls, the smaller "S" sizes can not be threaded together according to ASME code, but must be fusion welded, brazed, roll grooved, or joined with press fittings.īased on the NPS and schedule of a pipe, the pipe outside diameter (OD) and wall thickness can be obtained from reference tables such as those below, which are based on ASME standards B36.10M and B36.19M. By 1949 thinner schedules 5S and 10S, which were based on the pressure requirements modified to the nearest BWG number, had been created, and other "S" sizes followed later. Stainless steel pipes, which were coming into more common use in the mid 20th century, permitted the use of thinner pipe walls with much less risk of failure due to corrosion. Since the original schedules were created, there have been many revisions and additions to the tables of pipe sizes based on industry use and on standards from API, ASTM, and others. Also, in 1939, it was hoped that the designations of STD, XS, and XXS would be phased out by schedule numbers, however those original terms are still in common use today (although sometimes referred to as standard, extra-heavy (XH), and double extra-heavy (XXH), respectively). However these three sizes did not fit all applications. At that time only a small selection of wall thicknesses were in use: standard weight (STD), extra-strong (XS), and double extra-strong (XXS), based on the iron pipe size (IPS) system of the day. In March 1927 the American Standards Association authorized a committee to standardize the dimensions of wrought steel and wrought iron pipe and tubing. The term NB ( nominal bore) is also frequently used interchangeably with DN. The European and international designation equivalent to NPS is DN ( diamètre nominal/nominal diameter/Nennweite), in which sizes are measured in millimetres, see ISO 6708. NPS is often incorrectly called National Pipe Size, due to confusion with the American standard for pipe threads, " national pipe straight", which also abbreviates as "NPS". or Sch., for example – "2-inch diameter pipe, Schedule 40"). Specific pipe is identified by pipe diameter and another non-dimensional number for wall thickness referred to as the Schedule (Sched. "Nominal" refers to pipe in non-specific terms and identifies the diameter of the hole with a non-dimensional number (for example – 2-inch nominal steel pipe" consists of many varieties of steel pipe with the only criterion being a 2.375-inch (60.3 mm) outside diameter). Nominal Pipe Size ( NPS) is a North American set of standard sizes for pipes used for high or low pressures and temperatures. standard for the straight thread form on pipe (also abbreviated NPS), see National Pipe Thread. standard for pipe sizes, abbreviated NPS.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |